{{ hero.title }}

To determine how much dye is needed, reference this load size guide. If you are trying to achieve a very bold color, then double the dye ratio.

1. Before dyeing, remove any visible stains on the garment. This will help achieve uniform color results when dyeing. Pre-wash item in warm, soapy water without any fabric softener. This helps to remove any finishes that may interfere with dye absorption.
2. Wet fabric and place item(s) in the washing machine.
3. Set water temperature to the hottest possible setting and a wash cycle of at least 30 minutes or longer. The longer the item is in the dye, the darker the color will be.
4. Wearing rubber gloves, mix powder or well-shaken liquid dye with 4 cups 950 mL of very hot water. Stir well.
5. In a separate container, dissolve 1 cup 240 mL of salt in 4 cups 950 mL of very hot water if dyeing natural fibers like cotton or linen. If dyeing silk or nylon, mix 1 cup 240 mL of white vinegar with 2-4 cups 470-950 mL of hot tap water.
6. Add 1 teaspoon 5 mL of dish detergent to help promote level dyeing.
7. Start the cycle.
8. Remove detergent cup from detergent tray.
9. Pour the dye solution into the dispenser.  Then, pour the salt or vinegar solution. Flush the dispenser thoroughly with 4 cups 950 mL more of hot tap water.
10. To enhance the color and reduce color bleeding, use Rit ColorStay Dye Fixative immediately after dyeing and before washing, following these instructions.
11. Rewash item in warm water with mild detergent.
12. To clean the washing machine: Wipe around the inside of the lid and pour a little bleach through the internal dispenser (if there is one) as dyes can get into these areas. Then, fill washer to the highest water level there is and select the hottest water temperature setting. Add detergent with 2 cups 470 mL of chlorine bleach and run a full wash cycle with 3 old towels.

To determine how much dye is needed, reference this load size guide. 

1. Before dyeing, remove any visible stains on the garment. This will help achieve uniform color results when dyeing. Pre-wash item in warm, soapy water. This helps to remove any finishes that may interfere with dye absorption. Leave damp and set aside.
2. Shake liquid dye bottle and mix dye with 4 cups 950 mL of hot water. Powder dye should be pre-dissolved in 2 cups 470 mL of hot water. Add diluted dye to the basin.
3. If dyeing natural fibers like cotton or linen, mix 1 cup 240 mL of salt with 4 cups 950 mL of hot water. If dyeing silk or nylon, mix 1 cup 240 mL of white vinegar with 4 cups 950 mL of hot water. Add salt or vinegar solution to the basin.
4. Place wet item(s) in the washing machine.
5. Set water temperature to the hottest possible setting and a wash cycle of at least 30 minutes or longer and start the cycle.
6. Items should be in the dyebath for a minimum of thirty minutes to a maximum of one hour before the rinse cycle begins. Use an extended setting, or reset the setting before the rinse cycle starts to extend the wash time. Note that the longer the item is in the dyebath, the darker the color will be. For bulky items, such as draperies or large slipcovers, we recommend stopping the wash load periodically to detangle and unwind the item. This will help prevent uneven dyeing and lighter areas from forming. Remember to wear rubber gloves when handling the item mid-cycle.
7. To enhance the color and reduce color bleeding, use Rit ColorStay Dye Fixative immediately after dyeing and before washing, following these instructions.
8. Rewash item in warm water with mild detergent.
9. To clean the washing machine: Wipe around the inside of the lid and pour a little bleach through the internal dispenser (if there is one) as dyes can get into these areas. Then, fill washer to the highest water level there is and select the hottest water temperature setting. Add detergent with 2 cups 470 mL of chlorine bleach and run a full wash cycle with 3 old towels.